Panorama view of the mountains Hoher Kasten revolving restaurant Revolving restaurant with Demag drives in the Alps Eastern Switzerland has another tourist attraction to offer: a revolving restaurant has opened to offer visitors a panoramic view of the fascinating mountain landscape at a height of 1,795 m on the “Hoher Kasten” mountain in the Appenzell region. The special feature: a turning element in the floor enables the restaurant area to rotate once per hour. The drive systems required to make this happen – from the wheels to the frequency inverter – is "made by Demag". Appenzell mountain viewpoint in north-east Switzerland 1,795 m above sea level, high above Lake Constance, the Rhine valley and the Appenzell region Rotating restaurant with 360° panorama view The project The way to a peak experience A cable car is used to reach the “Hoher Kasten” revolving restaurant, in which LBHK Luftseilbahn Brülisau-Hoher Kasten AG invested some 9.6 million Swiss Francs. The trip from Brülisau to the mountain viewpoint takes almost 8 minutes. The idea to install a revolving disc in the floor was developed by the Swiss architects "architekten:rlc ag", based in Rheineck. Their overall concept won an architecture competition. Demag Cranes & Components supplied the drives for the application. The turntable, which consists of circular crane rails and a metal frame with a wooden floor mounted on top, measures 14.5 m in diameter. The structure is supported by 24 wheel blocks in size DRS 200 that are arranged in a circle and bolted to the concrete floor. Six DRS 112 wheel blocks serve as side guide rollers. The area inside the ring does not move. This is used to accommodate the open buffet of the panorama restaurant. The entire system revolves around this core element. The design principle of the Demag drive system already ensures that only a minimum of noise is generated in normal operation. Additional foam panels were installed as sound insulation and long-term graphite lubrication was applied to all of the drive elements. Foil separates the wood from the steel. The narrow gap between the outside and inside circles as closed with brush seals. The turntable is driven by six double offset gearboxes with brake motors, which are specifically rated for the very low speeds required for this application. The patented torque bracket of the offset gearboxes enables the torque to be transmitted from the geared motor to the wheel block without any radial force. This reduces the load on the drive shaft and extends its service life. The six drive motors are centrally controlled by a Demag Dedrive Compact frequency inverter, which results in very low operating noise at a modulation frequency of 16 kHz and provides for infinitely variable speeds. Technical data 18 DRS 200 wheel blocks Non-driven wheel blocks Travel wheel diameter: 200 D1= 200 mm, Travel wheel with convex tread and no flanges, R=450, 200 Travel wheel width: 101.0 mm, Travel wheel material: EN-GJS-700-2 spheroidal-graphite cast iron Wheel block prepared for top connection. 6 DRS 200 wheel blocks Driven wheel blocks, N 50 hub profile Travel wheel diameter: 200 D1= 200 mm Travel wheel with convex tread and no flanges, R=450, 200 Travel wheel width: 101.0 mm Travel wheel material: EN-GJS-700-2 spheroidal-graphite cast iron Wheel block prepared for top connection and torque bracket attachment MA200-1 DRS200 torque bracket sets 6 DRS wheel blocks Non-driven wheel blocks, for lateral guide arrangement Travel wheel diameter: 112 mm, without flanges Travel wheel material: EN-GJS-700-2 spheroidal-graphite cast iron Wheel block prepared for top connection. Demag double geared brake motors Type AME40DD DCF11DD ZBA 63 B4 B007, consisting of: AME40DD and DCF11DD double gearbox AC brake motor with ZBA 63B4 cylindrical-rotor motor B007 disc brake Voltage/frequency/current D/Y 220-380 V / 50 HZ / 1.50/0.85 A Output speed/output/CDF 1.12 rpm 0.18 KW 100% Motor speed 1390 rpm Brake torque/voltage/current 1.3 Nm / 180 V DC / 0.13 A with brake rectifier/voltage GE 400 V AC Enclosure: IP 54 Offset gearbox of torque arm design Solid shaft with involute splines 2 temperature detectors for cut-off at 155° C 1 operating terminal Fully wired in an electric enclosure with the following functions Turning ON, Stages 1-2-3, Turning OFF, Emergency stop. 1 control system with Demag Dedrive Compact frequency inverter For parallel control of the six drive motors Fully assembled and installed in an electric enclosure 16 kHz modulation frequency. Downloads Image Gallery Hoher Kasten revolving restaurant Hoher Kasten revolving restaurant Hoher Kasten revolving restaurant More Hoher Kasten revolving restaurant Image Gallery Hoher Kasten revolving restaurant The rotating restaurant is a new tourist attraction on the Hoher Kasten mountain. Hoher Kasten revolving restaurant Best panorama view: 1,795 metres above sea level Hoher Kasten revolving restaurant The turntable measures 14.5 m in diameter and rotates silently once per hour. Hoher Kasten revolving restaurant The turntable is safely supported by 24 DRS 200 that are arranged in a circle. Hoher Kasten revolving restaurant Six of the 24 DRS 200 wheel blocks, which are attached to the ground, are driven by Demag offset geared motors. Hoher Kasten revolving restaurant Precise turning motions for the panorama view provided by the Demag Dedrive Compact frequency inverter. Related products and services Analysis and consulting You can rely on our advice. At all times. Safety inspections Safeguarding you and your employees Inspection and maintenance Smooth and reliable. To ensure your equipment delivers performance.